Announcement

Collapse
No announcement yet.

WW #store

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

    WW #store

    8/9/2019 Update -

    Making motorcycle parts was always a passion and not for profit. Most of it was done below my actual cost with the rare occasion that I made a few bucks. It has become a burden to me so if you own a WW/R piece and like it, know that you own a limited edition. As inventory runs out, I will likely not restock anytime soon.

    Thank you everyone for your support.

    WW


    Everything that follows from here is legacy information only, and left for prosperity.

    Following footsteps of NT696 and organizing my bits into one location/thread instead of spamming up the forum elsewhere.

    "I'm a Hawk nut. Love these bikes. Have owned dozens of other bikes, ridden probably more than 100 different bikes, and always come back to the Hawk GT as it "Moves My Soul (slo1 TM )""

    I make a lot of little things for these wonderful beasts. Most are listed throughout this thread, and as time goes on and my website develops (no link yet - but yet, it exists) I'll clean all of this up and make it a bit more useful.

    NLA - Eccentric Spanners
    NLA - Custom subframes
    NLA - Custom triple clamps
    Tail Tidy kits
    California smog block off plates
    Ktech spanners
    ​​​​​​​NLA - Shock reservoir mounts
    ​​​​​​​NLA - Chain guard brackets
    ​​​​​​​NLA - Head light brackets and mounts
    ​​​​​​​NLA - Brembo brake hangers
    Ducati wheel cone spacers
    ​​​​​​​NLA - Modified rear brake rotors
    ​​​​​​​NLA - ​​​​​​​Spindle modifications to mount VFR, Ducati, or other wheels
    Jump plate kits (to move stock rear sets back and up - or down)
    ​​​​​​​NLA - Front fuel tank mounts



    California Hawk smog block off plates - aka WW#ASV block off plates. Buy them from Hordpower here: http://www.hordpower.com/index.php?m...roducts_id=578

    Or direct from me @ $39.00 per set shipped ConUS (as of 11/11/17 I have 2 sets black, and lots of polished/clear anodized left) - SEE POST #22 - historical thread here: http://www.hawkgtforum.com/forum/for...for-cali-heads


    IMG_3147.JPG

    ​​​​​​​
    Attached Files
    Last edited by wildwhl; 2 Weeks Ago.
    "It's better to burn out, than to fade away.

    #2



    WW#Spanner - V4.1 - also available at Hordpower.com.

    *Available in Type III Class II Red anodizing only now*

    V4.0 is $37.50 plus shipping



    Here's a picture of one grabbing a jacked up eccentric.




    Here's what it looks like on a decent eccentric.



    Still the 17mm spanner and neodymium magnet.





    Gratuitous porn shots

    Attached Files
    Last edited by wildwhl; 2 Weeks Ago.
    "It's better to burn out, than to fade away.

    Comment


      #3
      V3.0 Tail Tidy kits with LED - Kit includes tag mount, upper block off plate/LED mount, mini turn signal mounts and hardware (no electrical hardware is included).

      Complete kit is $99 shipped ConUS
      Upper light plate only, with LED (no hardware) $45 shipped ConUS
      Upper plate without LED provision (block off plate) $40 shipped ConUS (limited supply)
      (These work with the previous versions my tail tidy or the *HawkButt* by Dagus.)

      WW

      IMG_4619.JPG
      Attached Files
      Last edited by wildwhl; 03-25-2018, 05:54 PM.
      "It's better to burn out, than to fade away.

      Comment


        #4
        WW#Cowl Savers . . . and WW#Hook

        Pricing -
        $30 PLUS shipping = Savers including OEM Honda Grommets
        $25 PLUS shipping = Hooks in natural polish

        Buy both and save $$$ - $50 plus shipping

        If you don't use the hooks, you'll need spacers behind the cowl savers. I was going to supply those but have changed my mind - washers are functional if not pretty - and some have racks, etc. mounting here and may need a custom set of spacers. So washers on your end are the key - you'll need to space them out about .375". The point of the Hook is a simple tie down point (your bungy net, if you've carved off your lower grab rails, for example as well as spot to locate a tie down to keep the ass end of your bird from slip sliding away during transport - I'm sure you can imagine more uses than I can).





        Gamorg's Bike:
        Last edited by wildwhl; 2 Weeks Ago.
        "It's better to burn out, than to fade away.

        Comment


        • wildwhl
          wildwhl commented
          Editing a comment
          ...
          Last edited by wildwhl; 10-15-2016, 10:18 AM.

        #5
        Coming soon...
        Last edited by wildwhl; 2 Weeks Ago.
        "It's better to burn out, than to fade away.

        Comment


          #6
          Valve cover stand off spacers - anodized clear. These replace the valve cover bolt (included stainless hardware) and allow you to *bolt something there*. They're silly expensive to make (spacer+ (2) O rings + bolt) but that's my cost, go figure. Tell me how many you need and where shipped to - I'll send you total (PM's are best).

          $25 a set (pair), mailed USPS first class in the ConUS

          IMG_8109.jpg
          Last edited by wildwhl; 2 Weeks Ago.
          "It's better to burn out, than to fade away.

          Comment


            #7
            Brake Torsion arms - NLA


            8C41E676-9414-45F9-9CEB-72CCE0BDDF93.JPG
            Last edited by wildwhl; 2 Weeks Ago.
            "It's better to burn out, than to fade away.

            Comment


              #8
              NLA


              IMG_2082.JPG


              Last edited by wildwhl; 2 Weeks Ago.
              "It's better to burn out, than to fade away.

              Comment


                #9

                WW

                Last edited by wildwhl; 2 Weeks Ago.
                "It's better to burn out, than to fade away.

                Comment


                  #10
                  Remote shock reservoir mounts - NLA
                  Last edited by wildwhl; 2 Weeks Ago.
                  "It's better to burn out, than to fade away.

                  Comment


                    #11
                    Finally found my camera and got around to taking pics of the hole plug WW made. These are nice and fit snugly in place.....



                    Penske 8983, 3.0 jet kit, GVE's, RT springs, mikuni pump/cust mount, lightened rotor, Aztec8 Duals, EB harness,RX2N, Lenac brake kit/cust. reasets, CRG mirrors/levers, Full ti M4, Fabi hugger, Gino's roller, Brents frame slider, BTTs res elim., WW torsion bar, Eric'c cf sidestand and res bracket, Bogans Sprocket cover, plus much more
                    http://www.hawkgtforum.com/forum/showthread.php?t=17600

                    I also do decals for our Hawks and Bros on the forum. I do stock colors or custom colors. I can also do about any design out there or custom design you wish for.
                    link to the decals and pricing....
                    http://www.hawkgtforum.com/forum/hon...ics-and-prices

                    Comment


                      #12
                      Reserved
                      Last edited by wildwhl; 11-11-2017, 05:23 PM.
                      "It's better to burn out, than to fade away.

                      Comment


                        #13
                        Lower radiator stay - replaces part #19115-MN8-000

                        $25 shipped ConUS - includes stainless hardware.

                        Limited supply remain.

                        WW
                        Last edited by wildwhl; 06-26-2017, 09:07 AM.
                        "It's better to burn out, than to fade away.

                        Comment


                          #14
                          NLA
                          Last edited by wildwhl; 2 Weeks Ago.
                          "It's better to burn out, than to fade away.

                          Comment


                            #15

                            Comment

                            Working...
                            X